T
T
T
S
S
S
1
1
1
2
2
2
8
8
8
M
M
M
L
L
L
D
D
D
6
6
6
4
4
4
V
V
V
4
4
4
J
J
J
184PIN DDR400 Unbuffered DIMM
1024MB With 64Mx8 CL3
Transcend Information Inc.
10
SIMPLIFIED TRUTH TABLE (V=Valid, X=Don’t Care, H=Logic High, L=Logic Low)
COMMAND CKEn-1 CKEn /CS /RAS /CAS /WE BA0,1 A10/AP A0~A9, A11, A12 Note
Register
Extended
Mode Register Set
H X L L L L OP CODE 1,2
Register Mode Register Set H X L L L L OP CODE 1,2
Auto Refresh H 3
Entry
H
L
L L L H X
3
L H H H 3
Refresh
Self
Refresh
Exit L H
H X X X
X
3
Bank Active & Row Addr. H X L L H H V Row Address
Auto Precharge Disable L 4
Read &
Column Address
Auto Precharge Enable
H X L H L H V
H
Column
Address
(A0~A9)
4, 5
Auto Precharge Disable L 4
Write &
Column Address
Auto Precharge Enable
H X L H L L V
H
Column
Address
(A0~A9)
4, 5
Burst Stop H X L H H L X 6
Bank Selection V L
Precharge
All Banks
H X L L H L
X H
X
H X X X
Entry H L
L V V V
Active Power Down
Exit L H X X X X
X
H X X X
Entry
H L
L H H H
H X X X
Precharge Power
Down Mode
Exit
L H
L V V V
X
DM H X X 7
H X X X
No Operation Command
H X
L H H H
X
Note: 1. OP Code: Operand Code. A0 ~ A12 & BA0 ~ BA1: Program keys. (@EMRS/MRS)
2. EMRS/ MRS can be issued only at all banks precharge state.
3. Auto refresh functions are same as the CBR refresh of DRAM. The automatic precharge without row precharge command is meant by
"Auto". Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1: Bank select addresses. If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected. If both
BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank B is selected. If both BA0 is "Low" and BA1 is "High" at
read, write, row active and precharge, bank C is selected. If both BA0 and BA1 are "High" at read, write, row active and precharge, bank
D is selected.
5. If A10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected.
6. During burst write with auto precharge, new read/write command cannot be issued. Another bank read/write command can be issued
after the end of burst. New row active of the associated bank can be issued at tRP after the end of burst.
7. Burst stop command is valid at every burst length.
8. DM sampled at the rising and falling edges of the DQS and Data-in is masked at the both edges (Write DM latency is 0).
9. This combination is not defined for any function, which means "No Operation (NOP)" in DDR SDRAM.
(11 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji